SIM900 Breakout Board

手机数码 2013-09-30


After some months out, I come back with my last board, the SIM900 Breakout Board. It’s a board based on the popular SIM900 GSM modem, and I design to work with theDSETA boardI develop previously. Also, the board can be used without this board, I try to design it in the way that can be used with any microcontroller. From here, I want thanks to Ioannis Kedros from Embedded Day
his support in the design of the battery charger, and to Sonia Muñoz
, FAE from EBV, a great professional and a better friend, she always helps me when I need. So, let’s go to see what’s inside the board!


  • The Hardware

In this post, I only cover the hardware of the board. In an upcoming entry, I’ll develop a full application with this board and I cover the software aspects of the design.

This board is designed to use with a microcontroller-based board. It can be powered from a Li-Ion battery, so includes all the necessary electronic to charge and monitoring the battery. The schematics of the board can be downloadhere. As usually, the schematic is divided in functional blocks, and here’s a brief description of each:

Main Diagram
: All the blocks of the system are in this page, including the the relationship between all the signals. Note that with R35-R38, you can isolate the DTR, RI, NETLIGHT and INFO signals from the IO connectors, if you don’t populate.

IO Connectors
: This are the connection of the board with the rest of the world. It’s design to fit with the DSETA board, but you can use any other board or microcontroller to interface with it. The two connectors has 14 pins and has an standard 100 mils step. Here are the description of each pin of each connector:


Power Supply and Battery Charger
: This board can be powered from three different sources:

  1. Power supply from external +5V (+5V_EXT) using J3 connector.
  2. Power supply form the IO connectors (+5V_USB), using pins #2 from J1 or J2 connectors.
  3. Battery supply, using J4 connector.

To allow two external +5V power supplies, I use schottky rectifier diodes from Vishay ( SSA33L
) to parallelize it. I use this voltage to charge the battery, through the U1. I use the Microchip MCP73832T-2ACI/OT
battery charger. This device is a highly advanced linear charge management controller for Li-Ion and Li-Polymer batteries. As the battery has enough current to power the system, I fix the charge current at 100 mA, with a R4 value of 10K. The battery I use to power the system is the LP653450, a 3,7V / 1100mAh Li-Ion battery pack. The standard charging voltage for this battery is 4.2V, so the battery charger model must be fit with this requeriment. From this stage, two signals goes to the IO connectors: CHARGE_STATUS, a digital signal that indicates if the battery is charging (also, led D4 indicates the status visually), and BATT_VOLTAGE, an analog signal to measure the level of the battery. The second part of the schematic corresponds to the LDO regulator. This circuit used the input voltage to obtain the +3.0V necessary for the digital part. So, the microcontroller or board you use with this module must be fit to this voltage. The regulator is the TC1173-3.0VOA
from Microchip, that has a maximum dropout of 480mV. This regulator can give an output current of up 300mA, enough to power a board with a microcontroller. This output power supply is available in the IO connectors. And finally, the external +5V_EXT power supply is monitored with three independient circuits. Why? This is for a future application……stay tuned!

SIM900 Module
: The heart of the board. There’s a lot of information and breakout boards over the net, I gather info basically from the manufacturer
and from here
. Some tips about this part of the board:

  • C7 and C8 capacitors must be of 470uF or higer. Two capacitors of 100uF can’t absorb the current surges in transmission and reception modes and the module resets. With the highger capacities, this is resolved.
  • I use a right angle MMCX
    connector from Samtec. I want to use a SMA connector, but it’s size is prohibited.
  • I found the SIM connector in eBay
    . The schematic is the recommended in the SIM900 datasheet and works very fine.
  • Only TXD_GSM and RXD_GSM signals are necessary to work with the module. However, I also used more signals to work with the module, in the following pages I discuss about it.

Serial Ports
: All the serial port signals are adapted from 2.8V (SIM900 output) to the working voltage of 3.0V. To do this adaptation, a SN74LVC07
tri-state buffer is used. To the IO connectors, TXD, RXD, DTR and RI signals are carried. I also carried TXD and RXD debug port to an external connector, J7, for future uses.

SIM900 Signaling
: The last page is used from SIM900 status signals. RESET and ON_OFF signals are controlled from the microcontroller, in order to power-up properly the SIM900 module (you can see the power-on and power-off sequences in the datasheet here: SIM900_Hardware_Design_V2.03
). NETLIGHT and STATUS signals come from the SIM900 module. and can be used to supervise the status of the module. Both signals are carried to the IO connectors, so the microcontroller can read it. Also, both have a yellow led to visualize it:

NETLIGHT (D6): Network Status:

    • Off -> SIM900 is not running.
    • 64mS ON / 800mS OFF -> SIM900 not registered on the network
    • 64mS ON / 3000mS OFF -> SIM900 registered on the network
    • 64mS ON / 300 mS OFF -> GPRS communication established

STATUS (D7): Power On status:

    • Off (pin STATUS = 0) -> Module is power down
    • On (pin STATUS = 1) -> Module is power up

Some photos of the assemble board:

Top Layer

Top Layer (Another View)

Bottom Layer

Bottom Layer (Another View)

Top Layer with MMCX to SMA adaptor and Antenna

Top Layer with MMCX to SMA adaptor and Antenna (Detail)


  • PCB Design and mounting components

I try to perform the design in a 5cm x 5cm board, because I want that this board fits with the DSETA board. Also, I follow the PCB specifications from Dangerous Prototypes
, in order to use the DP5050
case also available at Seeedstudio. Another thing that I’ve got in mind is that I’ll mount the board by hand, so size components and distances must be enough to allow the manual mounting. The board is designed using Protel 2.71 and Protel 99SE to generate all the documentation, includinggerber files andtopographic schemes to placing the components. Again, I use the Seeed Studio PCB Fusion service
to order the boards. Now, they’ve the 100%E-Test at free of charge, a great notice because I think it’s a ‘must have’ feature for these kind of boards.


  • Integration with DSETA board

This board is originally designed to use in conjunction with theDSETA boardI develop before. So, after assembling the board, the next step is check that the two boards fits well. The result is great, here’re some pics of both boards:


In the next days, I’ll post an entry with an interesting application using these two boards. In this post, I’ll cover all the software aspects related to the communications with the SIM900 module.

责编内容by:Designing Electronics in Spain (源链)。感谢您的支持!

您可能感兴趣的

传亚马逊在做智能眼镜,集成Alexa智能语音功能... 网易科技讯 9月22日消息,亚马逊的Alexa助手平台在数年前成为Echo音箱的基础。虽然这种策略在最初遭受到质疑,但是亚马逊为Alexa平台招募了大量的研发人员,并且借助它打造出多种成功的设备。现在亚马逊公司或许正试图把Alexa塞进它最具野心的智能眼镜中。 谷歌公司为研发谷歌眼镜进行了...
暑期促销季 天猫热门手机TOP30排行榜 中关村在线消息:酷暑阻挡了多少小伙伴外出的计划,不过在家边吃习惯,边用手机看看电影玩玩手机或许也是消暑的绝佳选择,笔者在这里就给大家推荐几款天猫上最热销的30款手机,其中不乏影音性能各显其能,更是覆盖了高中低端各个价位的手机,最关键的是多款手机正在促销哦,不信就看看今天的天猫热门手机TOP30的报...
明明知道续航如尿崩,为什么手机电池容量却不能再做大些?... 目前智能手机的主要矛盾是日益增长的高性能同电池续航不给力之间的矛盾。 对于大多数的小伙伴来说,手机性能越来越强,应用的场景越来越丰富,但是偏偏这电池续航跟不上节奏了。 很多小伙伴抱怨 ,“我买的是旗舰机!为什么续航反而跟不上呢?” 虽然说旗舰手机是一家品牌的头牌,但是不代表就一定是在各方面...
不只有怪异前脸,吉利与沃尔沃打造了一台慷慨有为的混血车 | 董试... 究竟是吉利牌沃尔沃,还是沃尔沃牌吉利?想要向没听说过「领克」的人介绍这个新的汽车品牌时,这两个选项应该是最容易令人接受的说法了。 从去年新品牌亮相开始,领克就没有给市场大众太多的时间去熟悉自己的轶事,发布会上诸位外籍高管对于品牌理念的解读也屡屡被新车的风头盖过。直到 11 月...
First glance at the Cubot Note Plus camera-centric... Cubot seem to have finally joined all the main phone manufacturers and created a freshly designed handset that looks nothing like past Cubot devic...